Hello, welcome to the official website of WINDA Co., Limited!

De-palletizer Sizing: The 30 kg Reality

Release time:2026-11-16 14:20:00Number of views:

De-palletizing projects rarely fail on the robot. They fail on the load. A machine rated at 600 items per hour and 30 kg per item can look matched on paper and miss its business case in week three, because the pallets arriving at the dock are not the pallets in the brochure. This is a sizing guide to the WDA-DP-600: which number to buy on, and where the real limits sit.

Why 600 pph is the wrong number to buy on

Throughput is not one figure. It is a nominal rate divided by the events that interrupt a clean cycle. The WDA-DP-600 is rated at 600 items per hour, and the specification already notes this varies with item size and stacking condition. That caveat matters more than the headline.

Every interruption adds time: a re-grip after a partial clamp, a manual recovery when two cartons are fused by stretch film, a pause when vision re-plans on a shifted pattern, a stop for a damaged case.

Cycle eventAdded timeEffect at 600 pph nominal
Clean single-item cycleBaseline ~6 s600 items per hour
Two-item cycle (machine judges 1 or 2)~8-9 s for twoRaises rate; item counting matters
Re-grip on a partial clamp+4 to +7 s12 per hour cuts output 12-18%
Manual recovery of a fused case+20 to +60 sSix per shift cost 2-6 minutes

Buy against a measured re-grip rate, not the catalogue rate, and ask for the cycle-time distribution rather than the peak. A cell running 480 to 520 effective items per hour on your own load profile is well matched; 600 on demo pallets and 380 on yours is a year of defending the project.

The 30 kg ceiling and the loads that exceed it

The envelope is explicit: maximum item 600 x 600 x 500 mm, item weight 30 kg or less, flat pallets only. Item weight in most warehouses is not symmetrical. A median case might be 11 kg while the 99th percentile is 34 kg. The heavy tail is the dense product: liquid in glass, canned goods, bulk print. They are the cases where manual handling is most expensive and most injury-prone, and exactly the cases the machine is not rated for.

Plan a hybrid lane. The honest layout for a 30 kg machine is a robot lane plus a short manual or vacuum-lift lane for the oversize tail. Sizing the robot for the 99th percentile inflates cost for a load class that may be 1% of volume; sizing only for the robot pushes that 1% into an unplanned bottleneck.

Flat pallets only is the second constraint with a tail. Palletless loads, slip-sheet stacks and pallets with broken deck boards all appear in real inbound freight. A two-sided gripper tolerates imperfect pallet condition better than a top-vacuum head because it needs no flat sealed top surface, and because it pulls rather than lifts, the load path runs into the gripper body instead of hanging below it. It will still refuse a collapsed load.

WDA-DP-600 de-palletizer robot with two-sided gripper lifting cartons from a flat palletWDA-DP-600: orthogonal mechanism with a top-and-side gripper, 2.2 x 3.4 m footprint.

What the fenceless layout actually assumes

The machine occupies 2.2 m by 3.4 m by 2.7 m, excluding protruding parts, and can run without a safety fence or buffer area. In a brownfield warehouse that is worth real money, since every square metre of clearance is a pallet position lost. It also rests on assumptions worth checking.

  • Floor condition. Rated at 2300 kg or less with dynamic loads from the orthogonal mechanism. Slab flatness and point loading matter more when no fence absorbs an unexpected event.
  • Aisle definition. Fenceless is not unrestricted. Pedestrian and forklift routes still need marking and enforcement.
  • Local standard. Acceptance of fenceless operation is jurisdiction-specific. Verify it against the standard your insurer and safety auditor apply, in writing, before the layout is frozen.

Image recognition means buying a SKU library

The no-programming claim is accurate in that no robot teaching is needed for a new pattern, and incomplete in that recognition still needs to know what it is looking at. What you build during commissioning is a SKU library: the case types the cell will see, with dimensions, weights, surface finishes and pattern families. That library, not the robot, determines availability.

Write the SKU scope into the order. Specify how many families commissioning covers, how a new SKU is added afterwards, who does it and how long it takes. A machine that needs a service visit per new carton carries a hidden annual cost.

The 15% of the project nobody quotes

Cost elementWhy it existsPlanning note
Infeed conveyor and hand-offItems must land at a workable height and orientationFix interface geometry early; it constrains cycle time
Empty pallet stackerThe gripper does not move palletsCommonly omitted from first layouts
Compressed air supplyExcluded from the 6 kVA electrical figureSize for grip-cycle duty, not average flow
WCS, WMS or MES interfaceThe cell must know the next pallet and report resultsDefine message content and failure behaviour
Floor survey and anchoring2300 kg machine with dynamic loadsSurvey before delivery, not after

Utilities deserve their own line. Six kVA at three-phase 200 V, excluding compressors, means a transformer or dedicated supply in a plant on 380 V distribution. Ambient limits of 0 to 40 degrees Celsius and 20 to 90 percent RH non-condensing suit a warehouse but are tight for cold-store areas. Air is the item most often underestimated: grip cycles are short and frequent, so demand is peaky, and a compressor sized on average flow sags in the first hour of a shift. Lost clamp force then shows up as re-grips.

On labour, the honest framing of payback is headcount plus injury record. A cell at 500 effective items per hour across two shifts handles about 7,000 items per shift. Manual de-palletizing at 180 to 250 items per person-hour needs three to four operators to match, plus relief cover. It also tops most warehouse injury statistics, and insurers price that risk before a claim appears.

A two-week ramp instead of a one-day acceptance

  1. Days 1-2, clean loads. Single-SKU pallets in good condition. Record the baseline cycle-time distribution as the best case.
  2. Days 3-5, mixed patterns. Add pattern variation inside the commissioned families. Log every re-grip and intervention with a cause code; that distribution is the most valuable data the project produces.
  3. Days 6-9, tail and full shifts. Run the heavy tail and damaged cases deliberately, with real operators. Measure availability, not throughput alone: six good hours and two stopped hours is worse than a slower machine that never stops.
  4. Days 10-14, handover evidence. Fix effective rate, re-grip rate, intervention rate and SKU library contents in writing. Those four numbers are the contract for year one.

Specifying a de-palletizer for your own loads

Send actual load data rather than a generic enquiry: case dimensions and weights including the tail, pallet type and condition, pattern photographs, shift pattern, and the discharge height you must hit. WINDA can size the WDA-DP-600 against that profile and quantify the share of your volume inside the 30 kg and 600 x 600 x 500 mm envelope.

Related reading: de-palletizing automation in 2026, specifying a singulation cell by measurable KPIs, and telescopic belt conveyors at the dock door. Full specifications are on the WDA-DP-600 de-palletizer page.

Email: info [at] zowinda [dot] com  |  WhatsApp: +86 186 2085 0485